Is 10 AWG OK for 30A at 75 ft? — NEC Compliance Check

10 AWG copper: 30A ampacity, 4.66% voltage drop at 75 ft for 30A on 120V. NEC 2023 result: NOT compliant.

Load current (amps)

One-way distance (ft)

System voltage

Conductor

Insulation temp

Wire gauge to check

Max VD% (NEC rec 3%)

Phase

▸ Advanced options — derating, breaker & conduit

Conductors in raceway

Ambient temperature

Continuous load (3+ hrs)
Breaker ≥ 125% per NEC 210.19

FAIL

NEC 2023

Ampacity OKVD 4.66%

Upgrade to 8 AWG copper

Ampacity utilization100% of 30A

30A

Ampacity

at 60°C

24A

Continuous limit

80% of ampacity

4.66%

Voltage drop

5.59V

114.4V

At load

receiving end

30A

Breaker size

NEC 240.6(A)

~$108

Wire cost est.

150 ft THHN

3/4" EMT

Conduit size

3 conductors

10 AWG Cu

Ground wire (EGC)

NEC 250.122

162W

Power loss

~$198.67/yr

⚠Voltage drop 4.66% exceeds 3% limit. Min for VD: 8 AWG.

Is 10 AWG sufficient for 30A at 75 ft on 120V?

10 AWG copper has an ampacity of 30A at 60°C and 10,380 circular mils.

For a 30A load at 75 ft on 120V, the voltage drop is 5.59V (4.66%).

NEC result: ✗ NOT COMPLIANT — Voltage drop 4.66% exceeds 3% limit. Min for VD: 8 AWG.

Ampacity & voltage drop check

NEC 2023 Table 310.16. Voltage drop recommendation per NEC 215.2.

Metric	Value	Limit	Result
Wire ampacity	30A	≥ 30A	✓ OK
Utilization	100%	≤ 80% continuous	⚠
Voltage drop	5.59V	≤ 3% (3.6V)	✗ FAIL
Voltage drop %	4.66%	≤ 3%	✗ FAIL
Receiving voltage	114.4V	≥ 116V	⚠ LOW
NEC Compliance	NOT COMPLIANT	All checks pass	✗

Recommendation: Upgrade to 8 AWG

10 AWG does not meet NEC guidelines for this circuit. Upgrade to 8 AWG.

Voltage drop requires ≥ 16,126 CM → minimum 8 AWG.

Assumptions behind this wire check

Calculation assumes copper conductors, 60C insulation/terminal rating, single-phase power, not more than 3 current-carrying conductors, and 30C ambient unless the interactive calculator is changed.

Ampacity is based on NEC 2023 Table 310.16. Voltage drop uses the standard circular-mil formula and the branch-circuit planning target shown on the page.

The result checks conductor ampacity and voltage drop; it does not inspect breaker type, local amendments, conduit fill for mixed conductors, temperature at terminals, or equipment nameplate rules.

Safety and code review notes

Do not use a wire-size calculator as installation approval for energized work. Final conductor size must match the equipment nameplate, breaker, insulation, raceway, ambient temperature, and local code requirements.

Continuous loads, HVAC MCA/MOCP labels, aluminum terminations, wet locations, burial depth, and shared raceways can change the final legal wire size.

This scenario has warnings: Voltage drop 4.66% exceeds 3% limit. Min for VD: 8 AWG.

Nearby gauge alternatives for this load

Nearby AWG options for 30A at 75 ft on 120V. Use the final installation conditions before choosing a smaller conductor.

Gauge	Ampacity	Voltage drop	Receiving voltage	Modeled result
12 AWG	20A	7.41%	111.1V	Review
10 AWG	30A	4.66%	114.4V	Review
8 AWG	40A	2.93%	116.5V	Pass
6 AWG	55A	1.84%	117.8V	Pass
4 AWG	70A	1.16%	118.6V	Pass
3 AWG	85A	0.92%	118.9V	Pass
2 AWG	95A	0.73%	119.1V	Pass
1 AWG	110A	0.58%	119.3V	Pass

Breaker, ground wire, conduit, and loss planning

Planning values are contextual helpers. Breaker, EGC, and raceway choices must be checked against the real wiring method and local code.

Planning item	Computed value	Why it matters
Standard breaker	30A	NEC 240.6(A): use 30A breaker (next standard size ≥ 30A)
Continuous-load conductor limit	24A	Use when the load can run for 3 hours or more.
Copper EGC	10AWG	Equipment grounding conductor estimate from OCPD size.
Aluminum EGC	8AWG	Use only with listed aluminum grounding methods.
EMT conduit estimate	3/4"	3 modeled conductors; verify final fill by raceway and insulation.
Power loss	162W	1419.1 kWh/year at full-duty planning.

Derating sensitivity for this gauge

How 10 AWG ampacity changes as conductor count and ambient temperature increase.

Scenario	Conductor factor	Ambient factor	Derated ampacity	Signal
3 CCC / 30C	1	1	30A	Default conditions
4 CCC / 30C	0.8	1	24A	Derating applies
4 CCC / 40C	0.8	0.82	19A	Derating applies
6 CCC / 40C	0.8	0.82	19A	Derating applies
9 CCC / 50C	0.7	0.58	12A	Derating applies

Voltage drop derivation

Wire: 10 AWG copper — base 30A at 60°C | 10,380 CM,Derating: standard conditions (≤3 CCC, 30°C) — no derating → effective 30A,Ampacity check: 30A load vs 30A effective → ✓ OK (100%),Continuous limit (80%): 24A,Voltage drop: VD = (2 × 12.9 × 30A × 75ft) / 10,380 CM = 5.59V (4.66%),Receiving end: 114.4V — ✗ below limit,NEC compliance: ✗ NOT COMPLIANT — upgrade to 8 AWG,Breaker: NEC 240.6(A): use 30A breaker (next standard size ≥ 30A),Ground wire: NEC Table 250.122: 30A OCPD → EGC ≥ 10 AWG Cu (or 8 AWG Al),Power loss: 162W in run (I²R = 30² × 0.18Ω) — ~1419.1 kWh/yr (~$198.67/yr),Cost estimate: $0.72/ft × 150 ft = ~$108